Samsung washer error codes fall into a handful of groups: water not filling (4C, nF, 4E), water not draining (5C, SC, nd), the door not locking (dE, dS, LO), an unbalanced load (UE, Ub, U6) and too many suds (SUd, Sd). Most of these clear with a simple check you can do in ten minutes. This guide lists what each code means according to Samsung, what to try first and when the code points to a part that needs a technician.
Quick answer
- 4C, nF or 4E: the washer isn’t getting water. Check that both valves are fully open, the hoses aren’t kinked and hot goes to hot, cold to cold.
- 5C, SC or nd: it can’t drain. On a front loader, clean the pump filter behind the small panel at the bottom.
- UE, Ub or U6: the load is off balance. Spread the laundry out and press Start. Ur is only a “retrying” notice.
- dE, dS or LO: the door isn’t detected as locked. Check for clothing caught in the door and a damaged latch.
- Power off for 2 to 3 minutes and restart. If the same code comes back, it’s usually a valve, pump, lock, sensor or board: book a technician.
Samsung washer error codes list
Samsung uses several codes for the same problem because models display them differently (codes with a “1” in front, like 1 4C, belong to the same groups). A few codes mean different things on different models, so check your manual for dC and 3E.
| Code | Meaning | Try first | Call when |
|---|---|---|---|
| 4C, nF, 4E | Not filling | Open valves, straighten hoses, power off 1 minute | Water flows but the code returns |
| 4C2, 4E2, CE | Hot and cold hoses swapped | Red to red, blue to blue | Not a service code |
| 5C, SC, nd, 5E | Not draining | Clean the pump filter, check the drain hose | Filter clean, pump hums or is silent |
| OE, OC | Overflow, too much water | Power off, check the drain path | It fills with the power off |
| 1E, LE, LC | Water level or leak sensor | Look for leaks and suds | No leak, no suds, code stays |
| dE, dS, LO, FL | Door not closed and locked | Clear the seal, close firmly | Latch or lock damaged |
| dC | Door or unbalanced load (by model) | Check the manual, try both fixes | As for the door or load codes |
| UE, Ub, U6 | Unbalanced load | Spread the laundry, press Start | It happens on small, even loads |
| Ur | Rebalancing, only a notice | Nothing | Not needed |
| SUd, Sd, 5d | Too many suds | Less HE detergent | Not a service code |
| PF, 9C1, 9C2 | Power failure or voltage problem | Own circuit, no extension cord | Power is fine, code repeats |
| E2, bE2 | Button stuck | Power off, press each button | Button damaged or code returns |
| 3E, 3C, E3 | Motor (3E is voltage on some models) | Power off 2 to 3 minutes | It comes back |
| tE, HE, AE, IE, SF | Sensor, heater, communication or system | Power off 2 to 3 minutes | It comes back |
| Cb, dn, CL | Calibration, software update, Child Lock | Calibrate empty; let dn finish (about 15 minutes); turn Child Lock off | dn lasts over 30 minutes with Wi-Fi working |
Code meanings from Samsung’s US support page for washer information and error codes, checked November 2026. General information; your model’s manual has the final word.
Safety first
- Unplug the washer or switch off its breaker before you open the pump filter panel, pull the washer out or touch the hoses at the back.
- Turn both water valves off before you disconnect a supply hose.
- If the last cycle was hot (Sanitize, Self Clean, Pure Cycle), Samsung says to wait an hour before draining the water out of the filter.
- Don’t remove the screw that holds the drain hose clamp to the back of the washer. Don’t open the back or bottom panels or test the control board: that’s technician work.
How do I reset a Samsung washer error code?
Turn the washer off and unplug it or switch off its breaker for 2 to 3 minutes, then power it back on and restart the cycle. That’s Samsung’s general reset. It clears the display but not the cause: if the same code comes back, follow the steps for that code below. If the hoses are swapped (4C2, 4E2, CE), just reconnect red to red and blue to blue; Samsung says that code doesn’t need service.
4C, nF and 4E: washer not filling with water
Water isn’t reaching the tub fast enough. Usually it’s the supply, not the washer: a half-open valve, a hose kinked when the washer was pushed back, or a clogged inlet screen.

- Open both valves all the way and leave them open while the washer runs.
- Check the hoses. Pull the washer out a few inches and straighten any kink. Make sure hot goes to the hot inlet and cold to cold.
- Connect the hot line even if you only wash cold. Samsung says a washer without a hot line will show an error when it calls for hot water, and that can happen on cycles labeled Cold.
- Check the hose type. Samsung says not to use “Flood Safe” hoses on its washers.
- Check the drain hose depth. Samsung lists the drain hose too, because a hose pushed too far into the standpipe can siphon water out as fast as it fills. It should go 6 to 8 inches into the drain pipe.
- Power off for 1 minute, restore power and run a cycle.
- Clean the inlet screens. Valves off and washer unplugged, disconnect the hoses at the washer and clean any grit off the small screens in the inlets.
If the valves are open, water flows strongly from the hoses into a bucket, and the code still comes back, the water inlet valve or the water level sensor inside the washer is the likely cause. That’s a repair for a technician. Cost guides put an inlet valve replacement at $95 to $190 (Fixr) or $100 to $300 (HomeGuide), parts and labor included.
5C, SC and nd: Samsung washer not draining
A drain code means the water isn’t leaving the tub at the speed the washer expects. On a front loader, start with the pump filter (also called the debris filter). Samsung recommends cleaning it at least once a month or about every 40 washes, and a packed filter is a common reason for a drain code. Top-load Samsung washers don’t have a pump filter, so on those, start with the drain hose.

- Unplug the washer. If the last cycle was hot, wait an hour for the water to cool.
- Get ready for water: a towel and a shallow pan, like an oil drain pan. A full tub fills more than one.
- Open the access panel at the bottom front, pull out the small rubber drain hose and twist its cap off. Let the water drain out.
- Remove the filter by twisting it counterclockwise (some push in and twist, like a medicine bottle cap).
- Clean it with a soft brush and look into the opening at the pump impeller. If a sock, coin or bra wire is wedged against it, remove it.
- Reinstall the filter clockwise until it’s secure, cap the drain hose and clip it back in place, close the panel.
The steps above follow Samsung’s US guide to cleaning a front-load washer’s pump filter. Then check the drain hose for kinks and pour a bucket of water into the standpipe to see if it backs up.
If the filter is clean, the hose is clear and the washer still won’t drain, listen during the drain step. A hum with no water moving usually means the pump is jammed or failing. Silence can be the pump, its wiring or the control. Both need a technician. Pump replacement runs $150 to $350 per HomeGuide and $300 to $400 per Fixr.
UE, Ub and U6: unbalanced load codes
These codes mean the laundry has bunched up on one side of the drum, so the washer won’t spin at full speed. Untangle the load, spread it around the drum, close the door and press Start. A Ur code is different: Samsung says it only means the washer is adding water and trying to rebalance, and it doesn’t point to a problem.

Single heavy items (a bath mat, one pair of jeans) and sheets that knot around everything else cause most of these; add a couple of towels so the weight spreads. If UE or Ub shows on small, even loads, or the washer bangs and walks, check that it’s level; worn shock absorbers or springs are next. HomeGuide puts a full set of shock absorbers at $100 to $350 installed.
dE, dS and LO: door lock codes
The washer won’t start or keeps stopping because it can’t confirm the door is closed and locked. Open the door, pull any sock or sleeve out of the rubber seal, wipe the latch area, and close it firmly until it clicks. Samsung adds two notes that save service calls:
- If Child Lock is on and there’s water in the tub, a door code can show even when no cycle is running. Close the door or turn Child Lock off within 30 seconds, or the washer drains the tub.
- On FlexWash washers, a 1dC4 code can mean the small rubber button next to the upper washer’s latch is missing. Replacing the button fixes it.
A bent hook on the door, a cracked latch or a lock that clicks but never engages needs a new door lock. Fixr lists door lock replacement at $110 to $200.
SUd and Sd: the suds code
The washer found too much foam and paused so it can settle; the cycle then continues on its own. Samsung says this code doesn’t need service: it comes from too much detergent or a non-HE detergent. Use HE detergent to the line on the cap. Samsung’s steps for the 1E and LE leak codes also start with an empty cycle to check for suds.
Codes that usually need a technician
Motor (3E, 3C), sensor (tE, bE, 8E), heater (HE), communication (AE) and system (IE, SF) codes point at parts or electronics. Samsung’s only home step is a 2 to 3 minute power-off; the tests happen inside the cabinet with power applied, so they’re technician work.
What the parts behind common codes cost, parts and labor included (prices vary by model):
| Part behind the code | Fixr | HomeGuide |
|---|---|---|
| Water inlet valve (4C, OE) | $95 to $190 | $100 to $300 |
| Pressure switch / level sensor (1E, LE, OE) | $100 to $225 | $100 to $250 |
| Drain pump (5C, SC) | $300 to $400 | $150 to $350 |
| Door lock (dE, dS, LO) | $110 to $200 | $100 to $300 |
| Shock absorbers (UE, Ub) | $150 to $300 | $100 to $350 |
| Motor (3E, 3C) | $300 to $500 | $300 to $700 |
| Control board (AE, IE, SF) | $250 to $400 | $350 to $550 |
Sources: Fixr washing machine repair cost and HomeGuide washing machine repair cost, checked November 2026. Fixr puts the national average repair at $300.
Worked example: a 4C code that won’t clear
- Valves open, hoses straight, inlet screens clean, and the code still returns. The two likely parts are the inlet valve and the pressure sensor.
- If it’s the inlet valve, the cost guides above put the repair at roughly $95 to $300 installed.
- Even the top of that range matches Fixr’s $300 national average for a washer repair: a routine fix, not a reason to replace a washer that runs well.
- The ones that change the math are a motor or control board on an older washer. Our appliance repair cost guide and the appliance lifespan guide help you decide.
If the code keeps coming back after the checks, stop there. A Caspi Home Service technician can test the valve, pump, lock or sensor and give you an upfront price before any work starts. See our washing machine repair service and Samsung appliance repair pages.
PF and 9C codes after a storm in Florida and South Carolina
A PF code shows when the power went out before the washer finished, whether from an outage, a tripped breaker or someone unplugging it. The 9C codes point to irregular voltage. In Florida and South Carolina, outages come with summer thunderstorms and the Atlantic hurricane season, June 1 to November 30.
- A single PF after an outage isn’t a fault. Restart the cycle.
- Protect the board. Ready.gov notes that power can come back with momentary surges or spikes that can cause damage, and advises disconnecting appliances during an outage. Unplug the washer until power is steady.
- No extension cords. Samsung’s fix for voltage codes is a washer on its own circuit, plugged straight into the wall.
- Dead or erratic after a storm? A washer that won’t power on or shows random codes after a surge may have a damaged control board. That’s a technician repair, not a reset.
Frequently asked questions
What does 4C mean on a Samsung washer?
4C means the washer isn’t filling with water correctly. Open both water valves fully, straighten the hoses, make sure hot goes to hot and cold to cold, and power the washer off for a minute. If water flows strongly from the hoses and 4C keeps coming back, the inlet valve or water level sensor needs testing.
How do I fix the SC code on my Samsung washer?
SC is a no-drain code. Unplug the washer, drain the water through the small hose behind the bottom panel and clean the pump filter. Then check the drain hose for kinks. If the filter is clean and the washer still won’t drain, the pump is likely jammed or failing and needs a technician.
Why does my Samsung washer keep saying UE?
UE means the load is unbalanced, usually one heavy item or sheets wrapped around everything else. Spread the laundry around the drum and press Start. If UE shows on small, even loads, check that the washer is level; worn shock absorbers or suspension springs are the next suspects.
Why is my Samsung washer door stuck locked after a 4C code?
The door stays locked while there’s water in the tub above a safe level. Power the washer off and on, then run Drain/Spin if the water drains. If it won’t drain, unplug it and drain the tub through the pump filter hose. A door that stays locked with an empty tub points to the door lock.
Code still coming back?
Book a Caspi Home Service technician to find the part behind it. Same-day and next-day appointments are available, with a free estimate when you book online and no service-call fee.